ABNT Catálogo
ABNT Catálogo
Norma Técnica
Código
ASTM A633/A633M:13   CANCELADA
Código Secundário : A0633_A0633M-13
Data de Publicação : 15/10/2013
Título : Standard Specification for Normalized High-Strength Low-Alloy Structural Steel Plates
Comitê : A01.02 A01.02
Páginas : 3
Status : Cancelada  Substituída por : ASTM A633/A633M:18
Idioma : Inglês
Motivo do Cancelamento : 086290
Organismo : ASTM - American Society for Testing and Materials
Objetivo :

1.1 This specification covers normalized high-strength low-alloy structural steel plates for welded, riveted, or bolted construction.

1.2 This material is particularly suited for service at low ambient temperatures of −50°F [−45°C] and higher where notch toughness better than that expected in as-rolled material of a comparable strength level is desired.

1.3 Four grades, designated Grades A, C, D, and E (essentially former Specification A633 without a grade designation) are covered by this specification. Grade A provides a minimum yield point of 42 ksi [290 MPa] in thicknesses through 4 in. [100 mm], inclusive. Grades C and D provide a minimum yield point of 50 ksi [345 MPa] in thicknesses up to 2.50 in. [65 mm], inclusive and 46.0 ksi [315 MPa] in thicknesses over 2.50 in. to 4.0 in. [65 to 100 mm], inclusive. Grade E provides a minimum yield point of 60 ksi [415 MPa] in thicknesses up to 4.0 in. [100 mm], inclusive and 55 ksi [380 MPa] in thicknesses over 4 in. to 6 in. [100 to 150 mm], inclusive.

1.4 Current practice normally limits plates furnished under this specification to the maximum thicknesses shown in 1.3. The individual manufacturer should be consulted on size limitations for other product forms.

1.5 When the steel is to be welded, it is presupposed that a welding procedure suitable for the grade of steel and intended use or service will be utilized. See Appendix X3 of Specification A6/A6M for information on weldability.

1.6 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.

Normas Necessárias para a aplicação da ASTM A633/A633M:13
Normas Substitutas da ASTM A633/A633M:13
ASTM A633/A633M:18
ICS/CIN
77.140.10 - Aços tratados termicamente
Palavras-Chave
 
CURSOS (0 itens)
 
 
 
   
 
PUBLICAÇÕES (0 itens)
 
 
 
   

Informamos que a partir de 04/05/2020 atenderemos
em horário reduzido, das 9 h às 16 h, de segunda a sexta.

Suporte : (11) 3017-3621 suporte@abnt.org.br
Vendas: (11) 3017-3610 / 3648 / 3663 atendimento.sp@abnt.org.br
Certificação: (11) 3017-3691 certificacao@abnt.org.br
Informações sobre Cursos: Capacitacao (11) 97493-7688 / (11) 96419 -4720 cursos@abnt.org.br
Informações técnicas sobre normas: (11) 3017-3645 / 3646 cit@abnt.org.br
Copyright 2020© - Associação Brasileira de Normas Técnicas