ABNT Catálogo
ABNT Catálogo
Norma Técnica
Código
ASTM D2435/D2435M:11   CANCELADA
Código Secundário : D2435_D2435M-11
Data de Publicação : 01/05/2011
Título : Standard Test Methods for One-Dimensional Consolidation Properties of Soils Using Incremental Loading
Comitê : D18.05 D18.05
Páginas : 15
Status : Cancelada  Substituída por : ASTM D2435/D2435M:11(2020)
Idioma : Inglês
Motivo do Cancelamento : 077487
Organismo : ASTM - American Society for Testing and Materials
Objetivo : p id="s00002">1.1 These test methods cover procedures for determining the magnitude and rate of consolidation of soil when it is restrained laterally and drained axially while subjected to incrementally applied controlled-stress loading. Two alternative procedures are provided as follows:

1.1.1 Test Method AThis test method is performed with constant load increment duration of 24 h, or multiples thereof. Time-deformation readings are required on a minimum of two load increments. This test method provides only the compression curve of the specimen and the results combine both primary consolidation and secondary compression deformations.

1.1.2 Test Method BTime-deformation readings are required on all load increments. Successive load increments are applied after 100 % primary consolidation is reached, or at constant time increments as described in Test Method A. This test method provides the compression curve with explicit data to account for secondary compression, the coefficient of consolidation for saturated materials, and the rate of secondary compression.

Note 1—The determination of the rate and magnitude of consolidation of soil when it is subjected to controlled-strain loading is covered by Test Method D4186.

1.2 These test methods are most commonly performed on saturated intact samples of fine grained soils naturally sedimented in water, however, the basic test procedure is applicable, as well, to specimens of compacted soils and intact samples of soils formed by other processes such as weathering or chemical alteration. Evaluation techniques specified in these test methods assume the pore space is fully saturated and are generally applicable to soils naturally sedimented in water. Tests performed on other unsaturated materials such as compacted and residual (weathered or chemically altered) soils may require special evaluation techniques. In particular, the rate of consolidation (interpretation of the time curves) is only applicable to fully saturated specimens.

1.3 It shall be the responsibility of the agency requesting this test to specify the magnitude and sequence of each load increment, including the location of a rebound cycle, if required, and, for Test Method A, the load increments for which time-deformation readings are desired. The required maximum stress level depends on the purpose of the test and must be agreed on with the requesting agency. In the absence of specific instructions, Section 11 provides the default load increment and load duration schedule for a standard test.

Note 2—Time-deformation readings are required to determine the time for completion of primary consolidation and for evaluating the coefficient of consolidation, cv. Since cv varies with stress level and loading type (loading or unloading), the load increments with timed readings must be selected with specific reference to the individual project. Alternatively, the requesting agency may specify Test Method B wherein the time-deformation readings are taken on all load increments.

1.4 These test methods do not address the use of a back pressure to saturate the specimen. Equipment is available to perform consolidation tests using back pressure saturation. The addition of back pressure saturation does not constitute non-conformance to these test methods.

1.5 UnitsThe values stated in eith

Normas Necessárias para a aplicação da ASTM D2435/D2435M:11
Normas Substitutas da ASTM D2435/D2435M:11
ASTM D2435/D2435M:11(2020)
ICS/CIN
Palavras-Chave
 
CURSOS (0 itens)
 
 
 
   
 
PUBLICAÇÕES (0 itens)
 
 
 
   

Vendas: (11) 3017-3648 / 3663 / 3610 atendimento.sp@abnt.org.br
Informações sobre Cursos: Capacitacao (11) 3017-3680 / 3681 / 3683 cursos@abnt.org.br
Certificação: (11) 3017-3691 certificacao@abnt.org.br
Informações técnicas sobre normas: (11) 3017-3645 / 3646 cit@abnt.org.br
Suporte para visualização de normas : (11) 3017-3621 suporte@abnt.org.br
Copyright 2021© - Associação Brasileira de Normas Técnicas