ABNT Catálogo
ABNT Catálogo
Norma Técnica
Código
ASTM D256:2010   CANCELADA
Código Secundário : D0256-10E01
Data de Publicação : 01/05/2010
Título : Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics
Comitê : D20.10 D20.10
Páginas : 20
Status : Cancelada  Substituída por : ASTM D256:10(2018)
Idioma : Inglês
Motivo do Cancelamento : 092349
Organismo : ASTM - American Society for Testing and Materials
Objetivo :

1.1 These test methods cover the determination of the resistance of plastics to “standardized” (see Note 1) pendulum-type hammers, mounted in “standardized” machines, in breaking standard specimens with one pendulum swing (see Note 2). The standard tests for these test methods require specimens made with a milled notch (see Note 3). In Test Methods A, C, and D, the notch produces a stress concentration that increases the probability of a brittle, rather than a ductile, fracture. In Test Method E, the impact resistance is obtained by reversing the notched specimen 180° in the clamping vise. The results of all test methods are reported in terms of energy absorbed per unit of specimen width or per unit of cross-sectional area under the notch. (See Note 4.)

Note 1: The machines with their pendulum-type hammers have been “standardized” in that they must comply with certain requirements, including a fixed height of hammer fall that results in a substantially fixed velocity of the hammer at the moment of impact. However, hammers of different initial energies (produced by varying their effective weights) are recommended for use with specimens of different impact resistance. Moreover, manufacturers of the equipment are permitted to use different lengths and constructions of pendulums with possible differences in pendulum rigidities resulting. (See Section 5.) Be aware that other differences in machine design may exist. The specimens are “standardized” in that they are required to have one fixed length, one fixed depth, and one particular design of milled notch. The width of the specimens is permitted to vary between limits.

Note 2: Results generated using pendulums that utilize a load cell to record the impact force and thus impact energy, may not be equivalent to results that are generated using manually or digitally encoded testers that measure the energy remaining in the pendulum after impact.

Note 3: The notch in the Izod specimen serves to concentrate the stress, minimize plastic deformation, and direct the fracture to the part of the specimen behind the notch. Scatter in energy-to-break is thus reduced. However, because of differences in the elastic and viscoelastic properties of plastics, response to a given notch varies among materials. A measure of a plastic's “notch sensitivity” may be obtained with Test Method D by comparing the energies to break specimens having different radii at the base of the notch.

Note 4: Caution must be exercised in interpreting the results of these standard test methods. The following testing parameters may affect test results significantly:

Method of fabrication, including but not limited to proce

Normas Necessárias para a aplicação da ASTM D256:2010
Normas Substitutas da ASTM D256:2010
ASTM D256:10(2018)
ICS/CIN
29.035.20 - Isolantes elétricos a base de material plástico e borracha
Palavras-Chave
 
CURSOS (0 itens)
 
 
 
   
 
PUBLICAÇÕES (0 itens)
 
 
 
   

Informamos que a partir de 04/05/2020 atenderemos
em horário reduzido, das 9 h às 16 h, de segunda a sexta.

Suporte : (11) 3017-3621 suporte@abnt.org.br
Vendas: (11) 3017-3610 / 3648 / 3663 atendimento.sp@abnt.org.br
Certificação: (11) 3017-3691 certificacao@abnt.org.br
Informações sobre Cursos: Capacitacao (11) 97493-7688 / (11) 96419 -4720 cursos@abnt.org.br
Informações técnicas sobre normas: (11) 3017-3645 / 3646 cit@abnt.org.br
Copyright 2020© - Associação Brasileira de Normas Técnicas